Chulalongkorn University Theses and Dissertations (Chula ETD)
วิธีการเตรียมและขึ้นรูปอลูมินาเซรามิกสำหรับฉนวนหัวเทียน ด้วยวิธีโคลด์ไอโซสแททิกเพรสซิ่ง
Other Title (Parallel Title in Other Language of ETD)
Preparation and forming of alumina ceramic for spark plug insulator by cold isostatic pressing
Year (A.D.)
1995
Document Type
Thesis
First Advisor
เล็ก อุตตมะศิล
Faculty/College
Graduate School (บัณฑิตวิทยาลัย)
Degree Name
วิทยาศาสตรมหาบัณฑิต
Degree Level
ปริญญาโท
Degree Discipline
เทคโนโลยีเซรามิก
DOI
10.58837/CHULA.THE.1995.589
Abstract
การวิจัยครั้งนี้มีจุดหมายเพื่อศึกษาผลของตัวแปร 2 ตัวที่เกี่ยวข้องกับการขึ้นรูปอลูมินาเซรามิก สำหรับฉนวนหัวเทียนด้วยวิธีโคลด์ไอโซสแททิกเพรสซิ่ง คือความดันในการขึ้นรูปและอุณหภูมิในการเผาที่มีต่อโครงสร้างและสมบัติต่างๆ อันได้แก่ความแข็งแรง,ความต้านทานไฟฟ้าและความแข็งแรงทางไดอิเลกตริก ผลการวิจัยพบว่า การเพิ่มความดันในการขึ้นรูป และ/หรือ อุณหภูมิในการเผาจะทำให้ผลิตภัณฑ์มีความหนาแน่นสูงขึ้นและปริมาณรูพรุนลดลง ซึ่งจะช่วยทำให้สมบัติต่างๆ ที่กล่าวมาดีขึ้น แต่ในทางตรงกันข้ามก็จะทำให้ขนาดของเกรนใหญ่ขึ้น ซึ่งจะทำให้สมบัติต่างๆ ดังกล่าวด้อยลงไปเช่นเดียวกัน ดังนั้นเพื่อให้ได้ผลิตภัณฑ์ที่ดีที่สุด จึงควรจะใช้ความดันในการขึ้นรูปที่ต่ำ ประมาณ 100 เมกะปาสกาล แล้วจึงเผาที่อุณหภูมิปานกลาง ประมาณ 1600 องศาเซลเซียส ซึ่งจะได้ผลิตภัณฑ์ที่มีความหนาแน่นสูงถึงร้อยละ 97.65 ของความหนาแน่นทางทฤษฎี, ปริมาณรูพรุนร้อยละ 2.564 และการดูดซึมน้ำร้อยละ 0.687 ในขณะที่ขนาดของเกรนโดยเฉลี่ยประมาณ 3 ไมครอน
Other Abstract (Other language abstract of ETD)
The purpose of this investigation is to study effect of two factors, namely forming pressure and sintering temperature in producing alumina ceramic for spark plug insulator by cold isostatic pressing. These parameters which affect on microstructure and also certain properties such as strength, electric resistance and dielectric strength. The result of this research show that increasing pressure and/or sintering temperature will increase density and decrease porosity of product which render good properties. Increasing grain size will lower the properties. The suitable condition for the best quality of products will be low pressure approximately100 megapascal and 1600 celcius degree sintering temperature. At these condition, density will be 97.65 percent of theoretical density, porosity 2.564 percent, water absorption 0.687 and average grain size is approximate 3 micron.
Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-No Derivative Works 4.0 International License.
Recommended Citation
ไวทยวงศ์สกุล, สุรศักดิ์, "วิธีการเตรียมและขึ้นรูปอลูมินาเซรามิกสำหรับฉนวนหัวเทียน ด้วยวิธีโคลด์ไอโซสแททิกเพรสซิ่ง" (1995). Chulalongkorn University Theses and Dissertations (Chula ETD). 30335.
https://digital.car.chula.ac.th/chulaetd/30335